Beiträge von TERMINATOR

Zitat von Timm;127691

There is a sensor - the low-pressure sensor on the A/C system - if you have low gas pressure (or no gas pressure) then the auxiliary fan and the compressor will do nothing.

Then i need too check my pressure first;-)
Thanks Tim.

My fan on the AC radiator is not starting.. i put power directly on the fan, and the fan started up. So i know the fan isn't the problem
Is there a sensor somewhere that can be defect ? Or somthing else that's wrong ....?

Thanks!

Zitat von chadderz;117550

Check the wiring loom in the inner wheel well going to the ABS pump, it may look ok on the face of it but pull back some of the insulator where it bends slightly as it exits the wheel well toward the front of the car and you may find a broken or corroded wire. Key word may but it’s worth a shot.

Got any codes?

Chad

Alles anzeigen

I checked this, the wires looks ok..

Then i took out the ASC control unit, opend it and there was corrosion inside it. I cleaned it with electro cleaner and a tooth brush.
It got better, but still comes and goes..
I then opend it again, cleand it ones more, and now everything works fine

For years i have driven with this, finally its not a issue anymore!!

[IMG
Is this what you need Per ?][/IMG]
[/IMG]

I have one, from my 93 840ci.

Cobra springs : http://realcar.se/index.php?id…troller=product&id_lang=6

Zitat von HD;117863

Many many thanks - I have just purchased
Hayden

No problem, happy to help Hayden!

Here is one : http://www.ebay.co.uk/itm/BMW-…ts_SM&hash=item43c23bbc50

Zitat von Noggie;117750

Thanks guys, but I do want that plastic insert, like the one in my link.
i also see there are some with M symbols on, and a aluminium center
like this

http://www.ebay.com/itm/BMW-E9…-SHIFT-KNOB-/320816373231

you are not an easy man to please....
Its not ///M ... but how about ACS ??
8er.org/forum/index.php?attachment/25990/

HI Egil.
I have one, if you want a used one....
8er.org/forum/index.php?attachment/25985/8er.org/forum/index.php?attachment/25986/8er.org/forum/index.php?attachment/25987/8er.org/forum/index.php?attachment/25988/

Zitat von arnie;116175

Have you found the problem yet?

The usual cause of what you describe, as Timm has highlighted, is the ABS pump motor. Its location makes it susceptible to dirt, mud and rain.

The motor can be overhauled, but easier to sawp the motor or the whole hydraulic unit with one from an e39: 1996 - 2000 (after 2000, ABS system changed model).

The other cause could be water or moisture in your passenger door sill, which is where the control unit resides. If you had a windscreen replaced, check for water leaks.

Alles anzeigen

No arnie, still the same...

I had my whole hydraulic unit with the motor changed, it was from a e34, dont remember what year..
I also bought a "new" control unit, but no change..

Happy to help:)
Be careful not to break the "number 3" bolt , as its NLA..

I must say I am a bit confused .. why didnt he adjusted the rear wheels then ?? isnt that the normal procedure? to adjust all four wheels, when you're at it ...

Anyway.. for adjust the rear alignment, there is two eccentric bolts on each side.
Number 3 (camber) and 11(toe) on the picture:
8er.org/forum/index.php?attachment/25652/

Thanks Martin!

@ Christoph. I used black bumper spray,(spraybox). Got the tip from "KMS" from his Audio project: (http://www.8er.org/forum/showthread.php?14338-Audio-project)

Thanks, Thomas and Tim:)

After a couple of hours more work...

A few more pictures, with text..

8er.org/forum/index.php?attachment/25492/8er.org/forum/index.php?attachment/25493/8er.org/forum/index.php?attachment/25494/8er.org/forum/index.php?attachment/25495/8er.org/forum/index.php?attachment/25496/8er.org/forum/index.php?attachment/25497/8er.org/forum/index.php?attachment/25498/8er.org/forum/index.php?attachment/25499/8er.org/forum/index.php?attachment/25500/

Not sure what my next project will be, but you will be the first to know....

Upgrading the center console

Very happy with my cup holders , but it's time for a upgrade.
I now will install a coin holder. And here are some pictures of what i have done so far..

8er.org/forum/index.php?attachment/25480/8er.org/forum/index.php?attachment/25481/8er.org/forum/index.php?attachment/25482/8er.org/forum/index.php?attachment/25483/8er.org/forum/index.php?attachment/25484/8er.org/forum/index.php?attachment/25485/8er.org/forum/index.php?attachment/25486/8er.org/forum/index.php?attachment/25487/8er.org/forum/index.php?attachment/25488/8er.org/forum/index.php?attachment/25489/8er.org/forum/index.php?attachment/25490/8er.org/forum/index.php?attachment/25491/

Welcome to the forum aldialdi!

Good job! Just a tip.. a little description to each pics will make the thread it a little more interesting
I like the red car , no emblem in the front. Please put on some silver rims!

Zitat von huldra66;115743

Go to settings top right on screen then go to attachments left bottom and you will see your statistics and uploaded items as well as hove much you have left ; I have still only used aboust 1/5 on my limit.

Regards
Terje

Thanks Terje!

I have used under half the maximum limit, so clearly that's not why i had trouble uploading my pictures.
Must be something else...

Zitat von Richard.H;115735

In all the years so far I've noticed that dark faced gauges are a lot easier to read, day or night. White/silver gauges do look great but when the sun is shining down like here in Hong Kong or its very bright outside I've found they can glare quite a bit and sometimes they seem to "washout" the reading making it hard to read a gauge at a glance. Have never had that problem with darker faced gauges.

You might be right Richard.
Only had them installed for a few days , no problem so far... not much sun though